appealgrass5

How to Change a Subaru Spare Key If you've lost your Subaru car key, call a locksmith. They can usually cut keys for you cheaper than the dealer. Subaru car keys are generally either intelligent “push-to-start” fob remote keys or basic keys made of metal. The Fob key has to have its chip programmed. Keyless Entry System A key fob can be used to lock or unlock your Subaru from a distance. You can even open the trunk or lift gate of your vehicle. These remotes are connected to keys inside your car to connect with your computer system in your vehicle. Subaru models have a little known feature dubbed PIN Code Access. You can use a customized number sequence to start and open your vehicle. Read subaru flip key G28CarKeys to learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza. It's possible that the battery in the key fob is dying. You can test the battery life of your key fob using an instrument that is portable or a multimeter in your garage. The next step is to remove the circuit board for the transmitter from the key fob and examine it. You'll see two or three sets of 8-digits. Note the first one so you can remember it. After you've completed this, you can begin programming your key fob at home. This procedure differs based on the model and year your car. However, it's generally easy enough to do yourself. Key Fobs Subaru's newest models are all equipped with key fobs that don't just unlock the doors but also activate your lights, lock the gas cap, and even start your vehicle. This last feature is particularly beneficial if your experience includes arriving at the gas pump only to find that your car won't start because the battery in the key fob failed. If your Subaru is new or old it's likely that your key fob is able to be replaced with minimal difficulty. Remember that some of the most modern models, with the latest technology, might require visiting a dealer. With some effort and time, you can design your own key fob replacement. Begin by looking at the circuit board for the transmitter inside your key fob (instructions for opening the case should be included in the owner's manual). It should contain one or two sets of serial numbers each one of which is 8 digits long. Keep the first series of numbers for later for reference. Next, climb into your driver's seat and close all doors. Turn the key ten times to start your car, then switch off. Press the lock button on your key fob and then open the door to ensure that all of your doors work correctly. Then, close the door and remove the key from the ignition. You should hear your car sound again, signalling that the key fob is programmed. Ignition System If your Subaru keys aren't working as they should it could be because the key battery is dead. You can replace the battery in your key fob on your own if you know how. A replacement battery is not expensive and is fairly easy to locate. If the key fob doesn't respond to your commands, it could be a different issue. To get a spare, it's best to visit an authorized dealer. They will ensure that the key is an original Subaru key, which is covered under warranty, and that it will be programmed for your vehicle. This is a lot safer and simpler than buying an aftermarket key from a company on the internet. You can also request that the dealer cut a new key if you provide them with your VIN number as well as proof of ownership. This information is used to create a code for the replacement key so that it is recognized by your immobilizer. This process is more involved than cutting a new key and the dealership will usually charge more for this service. Once the new key has been programmed then you'll be able swap it with your current key. It will only take you five seconds to insert the new key, so keep your working key close to hand. Once the security light ceases to flash, you can remove the new key and test it to confirm it's functioning properly. Battery Replacement One of the most important characteristics that make Subaru fobs so valuable is their ability to turn on your car's power windows and sunroof with a single touch of a button. But, the battery in the Subaru key fob is not designed to last forever and will eventually require replaced. Fortunately, changing the battery is a simple procedure that you can do yourself with the help of this quick guide from Capitol Subaru. To start you'll need to find the tiny crevice inside the seam that divides the front and back of your key fob. With a small screwdriver, you can break the seam open and reveal a small compartment that houses the battery. Insert the new battery and ensure it is facing correctly. Remove the old one. After you've put everything together you can use the new key fob for locking or unlocking your vehicle. You should always have a spare set keys, especially if yours is damaged or lost. You can purchase a brand new key at your local dealership or get it cut by locksmiths. Either way, it's important to get your key fob operating properly as soon as you can to allow you to drive in a safe manner!